Set jockey pump pressure controls as a coordinated sequence derived from the approved system pressure and main fire pump start requirement. The jockey pump normally starts before the main fire pump as pressure falls and stops after restoring normal pressure. The main fire pump start point must remain low enough to avoid nuisance starts yet high enough to meet hydraulic and response requirements. There is no universal set of numbers: suction pressure, elevation, churn pressure, pressure regulation, sensing-line location, and device ratings all matter.
An toàn và phạm vi: Máy bơm phòng cháy chữa cháy và các thiết bị truyền động của chúng là thiết bị an toàn tính mạng. Công việc liên quan đến thủy lực, điện, dầu diesel, nhiên liệu, ắc quy, áp suất, thiết bị quay, thử nghiệm và khắc phục sự cố phải tuân theo thiết kế được phê duyệt hiện hành, hướng dẫn của nhà sản xuất, các tiêu chuẩn hiện hành và cơ quan có thẩm quyền. Hướng dẫn này giải thích lộ trình quyết định kỹ thuật; tài liệu này không cho phép thực hiện các thay đổi tại hiện trường, bỏ qua quy trình hoặc vận hành bởi nhân viên không đủ năng lực.
Establish the pressure basis
Use the normal static pressure, source variation, pump curves, elevation, system ratings, and approved hydraulic minimums. Confirm which gauge location defines each setting. Treat this as a system condition rather than an isolated component choice. Identify the source of every input, the unit used, the operating condition it represents, and the person responsible for approval. If information is preliminary, mark the assumption and test how the decision changes at a conservative boundary. This prevents a neat calculation from hiding an uncertain water level, pressure, valve position, driver condition, or simultaneous demand.
For jockey pump pressure settings, verify this section against the selected pump curve, the actual site arrangement, manufacturer instructions, and the current requirements accepted by the authority having jurisdiction. Check the installed condition as well as the drawing because pipe routes, elevations, supports, controls, and access often change during construction. Record the result in a form that can be repeated during commissioning and later inspection. Do not change a safety-critical setting or isolate fire protection without the approved impairment and restoration process.
Arrange the start sequence
As pressure falls, the jockey pump should receive the first maintenance call. Continued pressure loss from a real demand must then initiate the main fire pump. The most useful evidence is measured or approved project data, not a copied rule of thumb. Identify the source of every input, the unit used, the operating condition it represents, and the person responsible for approval. If information is preliminary, mark the assumption and test how the decision changes at a conservative boundary. This prevents a neat calculation from hiding an uncertain water level, pressure, valve position, driver condition, or simultaneous demand.
For jockey pump pressure settings, verify this section against the selected pump curve, the actual site arrangement, manufacturer instructions, and the current requirements accepted by the authority having jurisdiction. Check the installed condition as well as the drawing because pipe routes, elevations, supports, controls, and access often change during construction. Record the result in a form that can be repeated during commissioning and later inspection. Do not change a safety-critical setting or isolate fire protection without the approved impairment and restoration process.
Set jockey stop pressure
Choose a stop point the jockey pump can reliably reach without excessive deadheading or exceeding system ratings. Check its shutoff head. Review this condition at normal, test, and credible abnormal states before procurement. Identify the source of every input, the unit used, the operating condition it represents, and the person responsible for approval. If information is preliminary, mark the assumption and test how the decision changes at a conservative boundary. This prevents a neat calculation from hiding an uncertain water level, pressure, valve position, driver condition, or simultaneous demand.
For jockey pump pressure settings, verify this section against the selected pump curve, the actual site arrangement, manufacturer instructions, and the current requirements accepted by the authority having jurisdiction. Check the installed condition as well as the drawing because pipe routes, elevations, supports, controls, and access often change during construction. Record the result in a form that can be repeated during commissioning and later inspection. Do not change a safety-critical setting or isolate fire protection without the approved impairment and restoration process.
Protect the main pump start point
Do not set it so low that required residual pressure is lost before starting, or so high that normal pressure variation starts the main pump. The design team should turn this point into a traceable calculation or drawing note. Identify the source of every input, the unit used, the operating condition it represents, and the person responsible for approval. If information is preliminary, mark the assumption and test how the decision changes at a conservative boundary. This prevents a neat calculation from hiding an uncertain water level, pressure, valve position, driver condition, or simultaneous demand.
For jockey pump pressure settings, verify this section against the selected pump curve, the actual site arrangement, manufacturer instructions, and the current requirements accepted by the authority having jurisdiction. Check the installed condition as well as the drawing because pipe routes, elevations, supports, controls, and access often change during construction. Record the result in a form that can be repeated during commissioning and later inspection. Do not change a safety-critical setting or isolate fire protection without the approved impairment and restoration process.
Bảng quyết định thực tế
| Pressure event | Expected response | If incorrect, check |
|---|---|---|
| Small normal pressure loss | Jockey pump starts | Sensing line, controller, start setting |
| Pressure restored | Jockey pump stops | Stop setting, curve, leakage |
| Demand exceeds jockey capacity | Pressure continues to fall | Jockey size and test demand |
| Main start threshold reached | Main fire pump starts | Controller and sensing path |
| Main pump running | System follows approved stop logic | Controller mode and procedure |
| Frequent jockey cycles | Investigate leakage or control issue | Check valves, system volume, settings |
Use a reliable sensing line
Verify connection location, valve position, drainage, blockage risk, trapped air, and independence from pressure surges or an unrepresentative local point. Treat this as a system condition rather than an isolated component choice. Identify the source of every input, the unit used, the operating condition it represents, and the person responsible for approval. If information is preliminary, mark the assumption and test how the decision changes at a conservative boundary. This prevents a neat calculation from hiding an uncertain water level, pressure, valve position, driver condition, or simultaneous demand.
For jockey pump pressure settings, verify this section against the selected pump curve, the actual site arrangement, manufacturer instructions, and the current requirements accepted by the authority having jurisdiction. Check the installed condition as well as the drawing because pipe routes, elevations, supports, controls, and access often change during construction. Record the result in a form that can be repeated during commissioning and later inspection. Do not change a safety-critical setting or isolate fire protection without the approved impairment and restoration process.
Understand controller behavior
Review automatic start, manual stop or automatic-stop provisions as applicable, timer functions, alarms, and what happens after power restoration. The most useful evidence is measured or approved project data, not a copied rule of thumb. Identify the source of every input, the unit used, the operating condition it represents, and the person responsible for approval. If information is preliminary, mark the assumption and test how the decision changes at a conservative boundary. This prevents a neat calculation from hiding an uncertain water level, pressure, valve position, driver condition, or simultaneous demand.
For jockey pump pressure settings, verify this section against the selected pump curve, the actual site arrangement, manufacturer instructions, and the current requirements accepted by the authority having jurisdiction. Check the installed condition as well as the drawing because pipe routes, elevations, supports, controls, and access often change during construction. Record the result in a form that can be repeated during commissioning and later inspection. Do not change a safety-critical setting or isolate fire protection without the approved impairment and restoration process.
Diagnose cycling
Trend start and stop pressure, run time, leakage, check-valve condition, pressure tank where used, and gauge calibration before changing settings. Review this condition at normal, test, and credible abnormal states before procurement. Identify the source of every input, the unit used, the operating condition it represents, and the person responsible for approval. If information is preliminary, mark the assumption and test how the decision changes at a conservative boundary. This prevents a neat calculation from hiding an uncertain water level, pressure, valve position, driver condition, or simultaneous demand.
For jockey pump pressure settings, verify this section against the selected pump curve, the actual site arrangement, manufacturer instructions, and the current requirements accepted by the authority having jurisdiction. Check the installed condition as well as the drawing because pipe routes, elevations, supports, controls, and access often change during construction. Record the result in a form that can be repeated during commissioning and later inspection. Do not change a safety-critical setting or isolate fire protection without the approved impairment and restoration process.
Commission with controlled tests
Lower pressure slowly, record the jockey and main pump actions, verify stop behavior and alarms, then restore the system and secure settings. The design team should turn this point into a traceable calculation or drawing note. Identify the source of every input, the unit used, the operating condition it represents, and the person responsible for approval. If information is preliminary, mark the assumption and test how the decision changes at a conservative boundary. This prevents a neat calculation from hiding an uncertain water level, pressure, valve position, driver condition, or simultaneous demand.
For jockey pump pressure settings, verify this section against the selected pump curve, the actual site arrangement, manufacturer instructions, and the current requirements accepted by the authority having jurisdiction. Check the installed condition as well as the drawing because pipe routes, elevations, supports, controls, and access often change during construction. Record the result in a form that can be repeated during commissioning and later inspection. Do not change a safety-critical setting or isolate fire protection without the approved impairment and restoration process.
Điều này liên quan như thế nào đến thiết bị BORRAPUMP
BORRAPUMP cung cấp thiết bị bơm kỹ thuật cho các dự án cấp nước và phòng cháy chữa cháy. Xem lại phần liên quan Cấu hình sản phẩm BORRAPUMP làm điểm khởi đầu, sau đó gửi lưu lượng, cột áp, nguồn nước, động cơ, công suất, hệ thống điều khiển, điều kiện hiện trường, các yêu cầu hiện hành, số lượng và điểm đến được yêu cầu. Lựa chọn cuối cùng phải sử dụng cơ sở thủy lực của dự án và bản trình duyệt được phê duyệt; hướng dẫn này không khẳng định rằng một bố trí trong catalogue phù hợp với mọi khu vực tàijurisdiction hoặc rủi ro.
Các hướng dẫn BORRAPUMP liên quan
- lựa chọn cụm bơm phòng cháy chữa cháy
- Hướng dẫn kiểm tra nghiệm thu NFPA 20
- Hướng dẫn kiểm tra và thử nghiệm NFPA 25
Tài liệu tham khảo có thẩm quyền
Các nguồn sau đây thiết lập ranh giới tiêu chuẩn, bối cảnh an toàn phòng cháy chữa cháy và các nguyên tắc hệ thống bơm được sử dụng trong hướng dẫn này. Luôn áp dụng phiên bản và quy chuẩn địa phương được chấp thuận cho dự án.
- Trang phát triển tiêu chuẩn NFPA 25
- Trang phát triển tiêu chuẩn NFPA 20
- Tài nguyên hệ thống máy bơm của Bộ Năng lượng Hoa Kỳ
Video giáo dục
Nền tảng giáo dục bởi Practical Engineering: Máy bơm tạo ra áp suất hay lưu lượng?. Video hỗ trợ cho khái niệm kỹ thuật cơ bản và không thay thế các yêu cầu phòng cháy chữa cháy cụ thể của dự án.
Các câu hỏi thường gặp
What is the correct jockey pump pressure setting?
Use the project-specific approved sequence; no universal pressure value fits every system.
Should the jockey pump stop automatically?
Follow the listed controller and applicable project requirements. Main and jockey pump stop logic may differ.
Why does the main fire pump start before the jockey pump?
Check sensing lines, controller settings, source pressure changes, and whether the devices measure the same representative system point.
Can I widen the pressure gap to stop cycling?
Only after diagnosing leakage, check valves, system volume, pump curve, and applicable setting limits.
Danh sách kiểm tra xác minh cuối cùng
Trước khi phê duyệt, hãy xác nhận cơ sở thủy lực, điều kiện nguồn nước, đường cong bơm đã chọn, dữ liệu bộ truyền động và bộ điều khiển, định mức áp suất của các bộ phận, bố trí van, phương pháp thử nghiệm, lối đi, hệ thống thoát nước, cảnh báo và quy trình khôi phục. Giải quyết các khác biệt giữa bản vẽ và hệ thống thực tế đã lắp đặt. Trong quá trình chạy thử, hãy sử dụng các thiết bị đã hiệu chuẩn và ghi lại áp suất hút, áp suất xả, lưu lượng, tốc độ, tình trạng bộ truyền động, cảnh báo và các quan sát bất thường tại mọi điểm yêu cầu. Lưu giữ các kết quả đã được chấp nhận cùng với hồ sơ phòng bơm để các lần kiểm tra sau có thể so sánh các yếu tố tương đương.